Полетный стек SpeedyBee F405 V3 BLS 50A 30x30 FCESC Stack (SB-F4V3-50-STACK/HP0008.0094)

Name: Полетный стек SpeedyBee F405 V3 BLS 50A 30x30 FCESC Stack (SB-F4V3-50-STACK/HP0008.0094)
SKU: SB-F4V3-50-STACK/HP0008.0094
Price: 2802 UAH
Availability: OutOfStock

Код товара: SB-F4V3-50-STACK/HP0008.0094 Артикул: 12714

Все о товаре

Описание

Характерисики

Отзывы 0

Вопросы0

Хит

Продан

Полетный стек SpeedyBee F405 V3 BLS 50A 30x30 FCESC Stack (SB-F4V3-50-STACK/HP0008.0094)

Закінчився

2 802 ₴

Вес:13.8 г

Модель:F405 V3 BLS 50A 30x30 FCESC Stack

Размер:30.5 х 30.5 мм

Артикул:SB-F4V3-50-STACK/HP0008.0094

Виробник:SpeedyBee

Гарантія, міс:6

Гарантия, мес:1

Доставка

Курьером по Киеву

200

Курьером по Борисполю

Бесплатно

Новая почта

За тарифами перевозчика

ROZETKA Delivery

За тарифами перевозчика

Оплата

Гарантия от магазина

Полетный стек SpeedyBee F405 V3 BLS 50A 30x30 FCESC Stack (SB-F4V3-50-STACK/HP0008.0094)

2 802 ₴

Описание

MCU	STM32F405
IMU(Gyro)	BMI270
USB Port Type	Type-C
Barometer	Built-in
OSD Chip	AT7456E chip
BLE Bluetooth	Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)
WIFI	Not supported
DJI Air Unit Connection Way	Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug	Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Blackbox MicroSD Card Slot	*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card.
BetaFlight Camera Control Pad	Yes(CC pad on the front side)
Current Sensor Input	Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
Power Input	3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
5V Output	9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
9V Output	2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.
3.3V Output	Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output	Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal	M1 - M4 on bottom side and M5-M8 on front side.
UART	6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry	UART R5(UART5)
I2C	Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED Pad	Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer	BZ+ and BZ- pad used for 5V Buzzer
BOOT Button	Supported. [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input	Supported. Named as RS on the front side.
Smart Port / F.Port	Not supported
Supported Flight Controller Firmware	BetaFlight(Default), INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.)
Firmware Target Name	SPEEDYBEEF405V3
Mounting	30.5 x 30.5mm( 4mm hole diameter)
Dimension	41.6(L) x 39.4(W) x 7.8(H)mm
Weight	9.6g

Характеристики

Основные характеристики

Вес

13.8 г

Модель

F405 V3 BLS 50A 30x30 FCESC Stack

Размер

30.5 х 30.5 мм

Артикул

SB-F4V3-50-STACK/HP0008.0094

Виробник

SpeedyBee

Гарантія, міс

Країна виробництва

Китай

Микроконтроллер

STM32F405

Напряжение

3-6 В

Пиковый ток

55 A

Постоянный ток

50 А

Технические характеристики

Артикул

SB-F4V3-50-STACK/HP0008.0094

Гарантия, мес

Модель

F405 V3 BLS 50A 30x30 FCESC Stack

Производитель

SpeedyBee

Страна производства

Китай

Отзывы

Нет отзывов о данном товаре.

Нет отзывов о данном товаре, станьте первым, оставьте свой отзыв.

Вопросы и ответы

Добавьте вопрос, и мы ответим в ближайшее время.

Нет вопросов о данном товаре, станьте первым и задайте свой вопрос.